Health
and safety data sheets and information sheets for the HydrobreakÒ
Product Range
COMPANY
IDENTIFICATION: TechnoSol
Limited
Järvevana
st. 3a, 10132 Tallinn
EMERGENCY
TELEPHONE NUMBER: +372 51
61 403
HYDROBREAKÒ
2000
MARKET PLACE: As an alternative to dispersants, degreasers or detergents when dealing with hydrocarbons or oil pollution problems.
INDUSTRY
Water authorities, emergency services, oil distribution and manufacturing
and bioremediation.
PRODUCT A concentrated non-toxic hydrocarbon degrader
DESCRIPTION: with bio-acceleration properties. HYDROBREAKÒ 2000 has been formulated to have a high degree of cleaning/degreasing properties whilst still being totally biodegradable.
TYPICAL USES: HYDROBREAKÒ 2000 can be used as a cleaner degreaser along with the following additional applications. For use in conjunction with absorbents for dealing with hydrocarbon spills. For bioremediation and clean up of contaminated land. As part of a total hydrocarbon degrading package.
BENEFITS: Totally safe in use. Renders hydrocarbons non-flammable on application. Prevents grease and oil build-up. Aids biodegradation. Excellent cleaning/degreasing properties. Acts as a bioaccelerator for complete breakdown of hydrocarbons.
DILUTION RATES: Effective use up to 200:1
General minimum use 10:1
PACKAGING: 25 and 205 litre non-returnable containers.
TECHNICAL INFORMATION DATA - HYDROBREAKÒ
2000
PHYSICAL FORM: LIQUID
COMPOSITION OF PRODUCT: AN AQUEOUS BLEND OF FULLY BIODEGRADABLE SURFACTANTS, ORGANIC ACIDS AND PLANT EXTRACTS
APPEARANCE: COLOURLESS WITH A PALE YELLOW TINGE
ODOUR: SLIGHT
MISCIBILITY WITH WATER: COMPLETE
SPECIFIC GRAVITY @ 20 DEG C: 1.044-1.048
P.H.: 5.5 +/- 0.5
BOILING POINT: 100 DEG. C
FREEZING POINT: 0 DEG. C
FLASH POINT: > 65 DEG. C NON-FLAMMABLE
FLASH POINT METHOD: TCC (TAG CLOSED CUP)
DEGRADABILITY: > 97% GERMAN LAW
TRANSPORT INFORMATION: THIS PRODUCT IS NOT CONSIDERED HAZARDOUS FOR TRANSPORT
STORAGE REQUIREMENTS: STORE IN PLASTIC CONTAINERS ABOVE 0 DEG.C
SAFETY REQUIREMENTS: THIS PRODUCT IS CLASSIFIED NON-HARMFUL
WHILST THERE ARE NO SPECIFIC RECOMMENDATIONS WITH REGARD TO HYDROBREAK 2000, PROTECTIVE GOGGLES AND GLOVES SHOULD BE WORN WHEN HANDLING ANY SUBSTANCE
SAFETY
DATA SHEET
1.
IDENTIFICATION OF THE PREPARATION
SUBSTANCE NAME:
HYDROBREAKÒ
2000
COMPANY NAME:
TechnoSol Ltd
EMERGENCY TELEPHONE NUMBER:
+ 372 51 61 403
2.
COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT NAME
CONTENTS
HEALTH
RISK
(Class)
(R No.)
An aqueous blend of fully biodegradable
Surfactants, organic acids and plant extracts
none
none
3.
HAZARDS IDENTIFICATION
Not regarded as a health
hazard under current legislation
4. FIRST AID MEASURES
EYES:
Promptly wash eyes with lots of water while lifting the eyelids.
Get medical attention immediately. Continue to rinse.
SKIN:
Remove affected person from source of contamination.
Promptly flush contaminated skin with soap or mild detergent and water.
Promptly remove clothing if penetrated and flush the skin with water.
Get medical attention if irritation persists after washing.
INHALATION:
In the unlikely event of inhalation caused by faulty work practices, move
the exposed person to fresh air at once. Perform
artificial respiration if breathing has stopped.
Keep the affected person warm and at rest.
Get prompt medical attention.
INGESTION:
NEVER MAKE UNCONSCIOUS PERSON VOMIT OR DRINK FLUIDS! IF PERSON IS
CONSCIOUS, let affected person drink lots of water to dilute the swallowed
chemical. Seek medical attention.
5. FIRE FIGHTING MEASURES
HYDROBREAK 2000 is non-flammable and would
only cause problems under extreme conditions
EXTINGUISHING MEDIA:
alcohol foam carbon dioxide (CO2), dry chemicals, sand, dolomite,
etc. are unaffected by HYDROBREAKÒ
2000
SPECIAL FIRE FIGHTING
Use water to keep exposed containers
PROCEDURES:
cool and disperse vapours. Water
spray may be used to flush spills away from exposures and dilute spills.
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS:
monoxide (CO) could be given off under extreme conditions
6. ACCIDENTAL RELEASE MEASURES
SPILL CLEAN-UP METHODS:
Ventilate. Clean-up
personnel should use liquid contact protection.
Wash thoroughly after dealing with spillage.
SMALL SPILLS:
Absorb onto sand or other inert material and sweep up into suitable
container.
LARGE SPILLS:
Prevent the spillage from entering drains, ditches and rivers by use of
cellulose absorbents, sand or earth. Inform
local authorities if this cannot be prevented.
7.
HANDLING AND STORAGE
USAGE PRECAUTIONS:
Avoid spillage, skin and eye contact.
Avoid forming mists or fogs.
STORAGE PRECAUTIONS:
Store in plastic containers at temperatures above 0 degrees C. Keep
containers closed during storage.
8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
INGREDIENT NAME
STD
LT EXP
ST EXP
(8 hrs.)
(10 min.)
Does not apply
PROTECTIVE EQUIPMENT
Gloves and goggles should be worn when handling any chemical
RESPIRATORS:
No specific recommendations made.
PROTECTIVE GLOVES:
Use suitable protective gloves if risk of skin contact.
EYE PROTECTION:
Wear splash-proof eye goggles to prevent any possibility of eye contact.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
Liquid colourless or with pale yellow tint
ODOUR/TASTE:
Slight
SOLUBILITY DESCRIPTION:
Miscible with water
SPECIFIC GRAVITY (water = 1):
1.020 @ 20C
FLASH POINT (C):
>65 degree C. This
product is non-flammable
FLASH POINT METHOD
TCC (Tag closed cup)
10. STABILITY AND REACTIVITY
STABILITY:
No particular stability concerns
MATERIALS TO AVOID:
None
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon monoxide (CO) could be given off
under extreme conditions
11. TOXICOLOGICAL INFORMATION
TOXIC DOSE 1 (LD 50):
No information available
TOXIC CONS. (LC 50):
HEALTH WARNINGS:
May be an irritant of eyes and mucous membranes after prolonged exposure
HEALTH SYMPTOMS:
Irritation of eyes and mucous membranes
ACUTE AND CHRONIC
No known chronic or acute health risks.
HEALTH HAZARDS:
12. ECOLOGICAL INFORMATION
DEGRADABILITY:
>97% (German Law)
ACUTE FISH TOXICITY:
No information available
WATER HAZARD
May be slight pollutants based on reactants
CLASSIFICATION
13. DISPOSAL CONDITIONS
DISPOSAL METHODS:
Confirm disposal procedures with environmental engineer and local
regulations
14. TRANSPORT INFORMATION
UD No.:
This product is not considered hazardous
ADR CLASS No.:
for transport
AIR TRANSPORT CLASS:
-
AIR SUB-CLASS:
-
AIR PACK GR.:
-
HAZCHEM CODE:
-
SEA TRANSPORT CLASS No.:
-
SEA PACK GR.:
-
RAIL TRANSPORT CLASS No.:
-
CEFIC TEC (R) No.:
-
UK LABEL FOR CONVEYANCE:
-
PRODUCT COMMODITY CODE
3402 - 9010
15. REGULATORY INFORMATION
LABEL FOR SUPPLY:
No classification given
RISK PHRASES:
Not classified
SAFETY PHRASES:
Wear suitable gloves and eye protection (recommended)
UK REGULATORY REFERENCES:
Health and Safety at Work Act 1974. The Control of Substances Hazardous
to Health Regulations 1988 Chemical (Hazard Information and Packaging)
Regulations
16. OTHER INFORMATION
USER NOTES:
REVISION DATE:
1.10.00
REVISION NO./REPLACES
1/All previous health and safety
SDS ISSUED
data sheets
DISCLAIMER
THIS
INFORMATION RELATES ONLY TO THE SPECIFIC MATERIAL
DESIGNATED
AND MAY NOT BE VALID FOR SUCH MATERIAL USED IN COMBINATION WITH ANY OTHER
MATERIALS OR IN ANY PROCESS. SUCH
INFORMATION IS, TO THE BEST OF THE COMPANYS KNOWLEDGE AND BELIEF, ACCURATE
AND RELIABLE AS OF THE DATE INDICATED. HOWEVER,
NOR WARRANTY, GUARANTEE OR REPRESENTATION IS MADE AS TO ITS ACCURACY,
RELIABILITY OR COMPLETENESS. IT IS
THE USERS RESPONSIBILITY TO SATISFY HIMSELF AS TO THE SUITABILITY OF SUCH
INFORMATION FOR HIS OWN PARTICULAR USE.
HYDROBREAKÒ
PLUS
MARKET
PLACE:
For use anywhere that storage
space is at a premium or the use of a concentrate is acceptable for dealing with
hydrocarbon or aromatic pollution. Industry
effluent, treatment systems, spillage control kits, marine applications, export
markets.
PRODUCT
An ultra concentrated
non-toxic product capable
DESCRIPTION:
of dealing with the cleaning
of any oil, grease, fat or hydrocarbon problem. HYDROBREAKÒ PLUS
also has the ability to stimulate bacterial activity to breakdown the resultant
effluent into harmless by-products, i.e. water and carbon dioxide.
TYPICAL
USES:
HYDROBREAKÒ PLUS
can be used to perform the same operations as HYDROBREAKÒ 2000
as well as the following. It is an
excellent product for use through dosing units in effluent treatment plants for
the breakdown of hydrocarbons. Anywhere
that the storage of, or transportation of, bulk chemicals can present a problem.
With HYDROBREAKÒ PLUS
being an ultra concentrate, it allows users to store or transport smaller
quantities of product that can subsequently be diluted to the desired strength
using either fresh or sea water.
BENEFITS:
Totally safe in use.
Renders hydrocarbons non-flammable on application.
Prevents grease and oil build-up. Aids
biodegradation. Excellent cleaning
and degreasing properties. Ultra
concentrate allows for effective economical treatment of hydrocarbon and
aromatic waste.
DILUTION RATES:
Effective use up to 500:1
General minimum use 25:1
PACKAGING:
25 and 205 litre
non-returnable containers
TECHNICAL
INFORMATION DATA - HYDROBREAKÒ PLUS
PHYSICAL
FORM:
LIQUID
COMPOSITION
OF PRODUCT:
AN AQUEOUS BLEND OF FULLY BIODEGRADABLE SURFACTANTS, ORGANIC ACIDS AND
PLANT EXTRACTS
APPEARANCE:
COLOURLESS WITH A PALE YELLOW TINGE
ODOUR:
SLIGHT
MISCIBILITY
WITH WATER:
COMPLETE
SPECIFIC
GRAVITY @ 20 DEG C:
1.042-1.046
P.H.:
5.5 +/- 0.5
BOILING
POINT:
100 DEG. C
FREEZING
POINT:
0 DEG. C
FLASH POINT:
> 65 DEG. C NON-FLAMMABLE
FLASH POINT
METHOD:
TCC (TAG CLOSED CUP)
DEGRADABILITY:
> 97% GERMAN LAW
TRANSPORT
INFORMATION:
THIS PRODUCT IS NOT CONSIDERED HAZARDOUS FOR TRANSPORT
STORAGE
REQUIREMENTS:
STORE IN PLASTIC CONTAINERS ABOVE 0 DEG.C
SAFETY
REQUIREMENTS:
THIS PRODUCT IS CLASSIFIED NON-HARMFUL
PROTECTIVE GOGGLES AND GLOVES SHOULD BE WORN WHEN
HANDLING HYDROBREAK PLUS.
SAFETY
DATA SHEET
1.
IDENTIFICATION OF THE PREPARATION
SUBSTANCE NAME:
HYDROBREAKÒ PLUS
COMPANY NAME:
TechnoSol Ltd
EMERGENCY TELEPHONE NUMBER:
+ 372 51 61 403
2.
COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT NAME:
CONTENTS
HEALTH
RISK
(Class)
(R No.)
An aqueous blend of fully biodegradable
surfactants, organic acids and plant extracts
Xi
36,38
3.
HAZARDS IDENTIFICATION:
Based on the properties of the reactants this product should be classed
as a mild irritant.
4.
FIRST AID MEASURES:
EYES:
Promptly wash eyes with lots of water while lifting the eyelids.
Get medical attention immediately. Continue to rinse.
SKIN:
Remove affected person from source of contamination.
Promptly flush contaminated skin with soap or mild detergent and water.
Promptly remove clothing if penetrated and flush the skin with water.
Get medical attention if irritation persists after washing.
INHALATION:
In the unlikely event of inhalation caused by faulty work practices, move
the exposed person to fresh air at once. Perform
artificial respiration if breathing has stopped.
Keep the affected person warm and at rest.
Get prompt medical attention.
INGESTION:
NEVER MAKE UNCONSCIOUS PERSON VOMIT OR DRINK FLUIDS! IF PERSON IS
CONSCIOUS, let affected person drink lots of water to dilute the swallowed
chemical. Seek medical attention.
5.
FIRE FIGHTING MEASURES
HYDROBREAK PLUS is non-flammable and would only cause problems under
extreme conditions
EXTINGUISHING MEDIA:
alcohol foam carbon dioxide (CO2), dry chemicals, sand, dolomite,
etc. are unaffected by HYDROBREAKÒ PLUS.
SPECIAL FIRE FIGHTING:
Use water to keep exposed containers cool
PROCEDURES:
and disperse vapours. Water
spray may be used to flush spills away from exposures and dilute spills.
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS:
monoxide (CO) could be given off under extreme conditions
6.
ACCIDENTAL RELEASE MEASURES
SPILL CLEAN-UP METHODS:
Ventilate. Clean-up
personnel should use liquid contact protection.
Wash thoroughly after dealing with spillage.
SMALL SPILLS:
Absorb onto sand or other inert material and sweep up into suitable
container.
LARGE SPILLS:
Prevent the spillage from entering drains, ditches and rivers by use of
cellulose absorbents, sand or earth. Inform
local authorities if this cannot be prevented.
7.
HANDLING AND STORAGE
USAGE PRECAUTIONS:
Avoid spillage, skin and eye contact.
Avoid forming mists or fogs.
STORAGE PRECAUTIONS:
Store in plastic containers at temperatures above 0 degrees C. Keep
containers closed during storage.
8.
EXPOSURE CONTROLS AND PERSONAL PROTECTION
INGREDIENT NAME:
STD
LT EXP
ST EXP
(8 hrs.)
(10 min.)
PROTECTIVE EQUIPMENT:
Gloves and goggles should be worn when handling any chemical
RESPIRATORS:
No specific recommendations made.
PROTECTIVE GLOVES:
Use suitable protective gloves if risk of skin contact.
EYE PROTECTION:
Wear splash-proof eye goggles to prevent any possibility of eye contact.
9.
PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
Liquid colourless or with a pale yellow tint
ODOUR/TASTE:
Slight
SOLUBILITY DESCRIPTION:
Miscible with water
SPECIFIC GRAVITY (Water = 1):
1.044 @ 20C
FLASH POINT (C):
>65 degree C. This
product is non-flammable
FLASH POINT METHOD:
TCC (Tag closed cup)
10. STABILITY
AND REACTIVITY
STABILITY:
No particular stability concerns
MATERIALS TO AVOID:
None
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS
monoxide (CO) could be given off under extreme conditions
11. TOXICOLOGICAL
INFORMATION
TOXIC DOSE 1 (LD 50):
No information available
TOXIC CONS. (LC 50):
HEALTH WARNINGS:
May be an irritant of eyes and mucous membranes
HEALTH SYMPTOMS:
Irritation of eyes and mucous membranes
ACUTE AND CHRONIC
No known chronic or acute health risks
HEALTH HAZARDS:
12. ECOLOGICAL
INFORMATION
DEGRADABILITY:
>97% (German Law)
ACUTE FISH TOXICITY:
No information available
WATER HAZARD
May be slight pollutants based on
CLASSIFICATION:
reactants
13. DISPOSAL
CONDITIONS
DISPOSAL METHODS:
Confirm disposal procedures with environmental engineer and local
regulations
14. TRANSPORT
INFORMATION
UD No.:
This product is not considered hazardous
ADR CLASS No.:
for transport
AIR TRANSPORT CLASS:
-
AIR SUB-CLASS:
-
AIR PACK GR.:
-
HAZCHEM CODE:
-
SEA TRANSPORT CLASS No.:
-
SEA PACK GR.:
-
RAIL TRANSPORT CLASS No.:
-
CEFIC TEC (R) No.:
-
UK LABEL FOR CONVEYANCE:
-
PRODUCT COMMODITY CODE
3402 - 9010
15. REGULATORY
INFORMATION
LABEL FOR SUPPLY
RISK PHRASES:
-
SAFETY PHRASES:
37/39 Wear suitable gloves and eye
protection
26
In case of contact with eyes wash immediately with plenty of water and
seek medical advice
28
After contact with skin wash immediately with plenty of water.
UK REGULATORY REFERENCES:
Health And Safety At Work Act 1974. The Control of Substances Hazardous
to Health Regulations 1988 Chemical (Hazard Information and Packaging)
Regulations
16. OTHER
INFORMATION
USER NOTES:
REVISION DATE:
1.10.00
REVISION NO./REPLACES
1/All previous health and safety
SDS ISSUED:
data sheets
DISCLAIMER
THIS INFORMATION RELATES ONLY TO THE SPECIFIC
MATERIAL DESIGNATED AND MAY NOT BE VALID FOR SUCH MATERIAL USED IN COMBINATION
WITH ANY OTHER MATERIALS OR IN ANY PROCESS.
SUCH INFORMATION IS, TO THE BEST OF THE COMPANYS KNOWLEDGE AND BELIEF,
ACCURATE AND RELIABLE AS OF THE DATE INDICATED.
HOWEVER, NOR WARRANTY, GUARANTEE OR REPRESENTATION IS MADE AS TO ITS
ACCURACY, RELIABILITY OR COMPLETENESS. IT
IS THE USERS RESPONSIBILITY TO SATISFY HIMSELF AS TO THE SUITABILITY OF SUCH
INFORMATION FOR HIS OWN PARTICULAR USE.
HYDROBREAKÒ
POWER
MARKET PLACE:
As an alternative to dispersants, degreasers or
detergents for dealing with heavy fuel oils and greases as well as aged oil
contamination. Extremely effective in soil cleaning applications.
Industry, local authorities,
tank cleaning, oil distribution and manufacturing and soil cleaning companies.
PRODUCT DESCRIPTION: A concentrated non-toxic
hydrocarbon degrader with bio-acceleration properties.
HYDROBREAKÒ POWER has been formulated to
be very effective on stubborn oils, greases, tars and waxes, whilst at the same
time being totally safe and environmentally acceptable.
TYPICAL USES:
HYDROBREAKÒ POWERS unique formulation
allows it to be used for removing the toughest deposits of heavy fuel oils,
greases, tars, waxes and aged oil contamination.
It is especially recommended for tar manufacturers, road laying companies
and local authorities to clean tar spraying equipment and machinery, as well as
for the cleaning of heavy fuel and oil deposits from concrete. HYDROBREAKÒ POWER should also be used for
cleaning components, tanks, etc. contaminated with heavy grease deposits, where
excellent results will be achieved. It has also been proved to be very effective
in cleaning contaminated land.
BENEFITS:
Totally safe in use.
Renders hydrocarbons non-flammable.
Prevents grease and oil build-up. Aids biodegradation. Excellent
cleaning/degreasing properties. Acts
as a bioaccelerator for complete breakdown of hydrocarbons.
APPLICATION METHODS: Pressure
washers/steam cleaner, floor scrubbing machines or by hand. By injection or
rotovator for soil cleaning
DILUTION RATES:
Effective use up to 100:1
General minimum use 10:1
PACKAGING:
20 and 205 litre
non-returnable containers
TECHNICAL INFORMATION DATA -
HYDROBREAKÒ
POWER
PHYSICAL
FORM:
LIQUID
COMPOSITION
OF PRODUCT:
AN AQUEOUS BLEND OF FULLY BIODEGRADABLE SURFACTANTS, ORGANIC ACIDS,
RENEWABLE NATURAL SOLVENTS AND PLANT EXTRACTS
APPEARANCE:
YELLOW/ORANGE
ODOUR:
DISTINCT
MISCIBILITY
WITH WATER:
COMPLETE
SPECIFIC
GRAVITY @ 20 DEG.C:
0.978
P.H.:
6.0 +/- 0.5
BOILING
POINT:
100 DEG. C
FREEZING
POINT:
0 DEG. C
FLASH POINT:
> 65 DEG. C NON-FLAMMABLE
FLASH POINT
METHOD:
TCC (TAG CLOSED CUP)
DEGRADABILITY:
> 97% GERMAN LAW
TRANSPORT
INFORMATION:
THIS PRODUCT IS NOT CONSIDERED HAZARDOUS FOR TRANSPORT
STORAGE
REQUIREMENTS:
STORE ABOVE 0c
SAFETY
REQUIREMENTS:
THIS PRODUCT IS CLASSIFIED NON-HARMFUL
WHILST THERE ARE NO SPECIFIC RECOMMENDATIONS WITH
REGARD TO HYDROBREAK POWER, PROTECTIVE GOGGLES AND GLOVES SHOULD BE WORN WHEN
HANDLING ANY SUBSTANCE.
SAFETY
DATA SHEET
1.
IDENTIFICATION OF THE PREPARATION
SUBSTANCE NAME:
HYDROBREAKÒ
POWER
COMPANY IDENTIFICATION:
TechnoSol Ltd
Emergency
Telephone Number:
+ 372 51 61 403
2.
COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT NAME
CONTENTS
HEALTH
RISK
(class)
(R No.)
An aqueous blend of natural renewable
solvents, fully biodegradable
surfactants, organic acids and plant extracts
XI
irritating to
respiratory
system and
skin
3.
HAZARDOUS IDENTIFICATION
Irritating to respiratory system and skin.
4.
FIRST AID MEASURES
EYES:
Promptly wash eyes with lots of water while lifting the eye lids.
Get medical attention immediately. Continue to rinse.
SKIN:
Remove affected person from source of contamination.
Promptly flush contaminated skin with soap or mild detergent and water.
Promptly remove clothing if penetrated
and flush the skin with water. Get
medical attention if irritation persists after washing.
INHALATION:
In the unlikely event of inhalation caused by faulty work practices, move
the exposed person to fresh air at once. Perform
artificial respiration if breathing has stopped.
Keep the affected person warm and at rest. Get prompt medical attention.
INGESTION:
NEVER MAKE AN UNCONSCIOUS PERSON VOMIT OR DRINK FLUIDS! IF PERSON IS
CONSCIOUS, let affected person drink lots of water to dilute the swallowed
chemical. Seek medical attention.
5.
FIRE FIGHTING MEASURES
HYDROBREAK POWER is non-flammable and would only cause problems under
extreme conditions
EXTINGUISHING MEDIA
alcohol foam carbon dioxide (CO2), dry chemicals, sand , dolomite ,
etc. are unaffected by HYDROBREAKÒ POWER
SPECIAL FIRE FIGHTING
Use water to keep exposed containers cool
PROCEDURES:
and disperse vapours. Water
spray may be used to flush spills away from exposures and dilute spills
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS:
monoxide (CO) could be given off under extreme conditions
6.
ACCIDENTAL RELEASE MEASURES
SPILL CLEAN-UP METHODS:
Ventilate. Clean-up
personnel should use liquid contact protection.
Wash thoroughly after dealing with spillage.
SMALL SPILLS:
Absorb onto sand or other inert material and sweep up into suitable
container.
LARGE SPILLS:
Prevent the spillage from entering drains, ditches and rivers by use of
cellulose absorbents, sand or earth. Inform
local authorities if this cannot be prevented.
7.
HANDLING AND STORAGE
USAGE PRECAUTIONS:
Avoid spillage, skin and eye contact.
Avoid forming mists or fogs.
STORAGE PRECAUTIONS:
Store at temperatures above 0 degrees C. Keep containers closed during
storage. Store in containers supplied.
8.
EXPOSURE CONTROLS AND PERSONAL PROTECTION
INGREDIENT NAME:
STD
LT EXP
ST EXP
(8 hrs.)
(10 min.)
PROTECTIVE EQUIPMENT
Protective gloves and goggles should be worn
RESPIRATORS:
No specific recommendations made
PROTECTIVE GLOVES:
Use suitable protective gloves if risk of skin contact.
EYE PROTECTION:
Wear splash-proof eye goggles to prevent any possibility of eye contact.
9.
PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
Yellow/orange
ODOUR/TASTE:
Distinct
SOLUBILITY DESCRIPTION:
Miscible with water
SPECIFIC GRAVITY (Water = 1):
0.978 @ 20C
FLASH POINT (C):
>65 degree C. This
product is non-flammable
FLASH POINT METHOD
TCC (Tag closed cup)
10.
STABILITY AND REACTIVITY
STABILITY:
No particular stability concerns
MATERIALS TO AVOID:
None
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon monoxide (CO) could be given off
under extreme conditions
11.
TOXICOLOGICAL INFORMATION
TOXIC DOSE 1 (LD 50):
No information available
TOXIC CONS. (LC 50):
HEALTH WARNINGS:
May be an irritant of eyes and mucous membranes.
HEALTH SYMPTOMS:
Irritation of eyes and mucous membranes
ACUTE AND CHRONIC
No known chronic or acute health risks
HEALTH HAZARDS:
12.
ECOLOGICAL INFORMATION
DEGRADABILITY:
>97% (German Law)
ACUTE FISH TOXICITY:
No information available
WATER HAZARD:
May be slight pollutant based on reactants
CLASSIFICATION
13.
DISPOSAL CONDITIONS
DISPOSAL METHODS:
Confirm disposal procedures with environmental engineer and local
regulations
14.
TRANSPORT INFORMATION
UD No.:
This product is not considered hazardous
ADR CLASS No.:
for transport
AIR TRANSPORT CLASS:
-
AIR SUB-CLASS:
-
AIR PACK GR.:
-
HAZCHEM CODE:
-
SEA TRANSPORT CLASS No.:
-
SEA PACK GR.:
-
RAIL TRANSPORT CLASS No.:
-
CEFIC TEC (R) No.:
-
UK LABEL FOR CONVEYANCE:
-
PRODUCT COMMODITY CODE
3402 - 9010
15.
REGULATORY INFORMATION
LABEL FOR SUPPLY:
- No irritant
RISK PHRASES:
Not classified
SAFETY PHRASES:
Wear suitable gloves and eye protection. (Recommended)
UK REGULATORY REFERENCES:
Health and Safety at Work Act 1974. The Control of Substances Hazardous
to Health Regulations 1988 Chemical (Hazard Information and Packaging)
Regulations
16.
OTHER INFORMATION
USER NOTES:
REVISION DATE:
1.10.00
REVISION NO./REPLACES
1/All previous health and safety
SDS ISSUED
data sheets
DISCLAIMER
THIS INFORMATION RELATES ONLY
TO THE SPECIFIC MATERIAL DESIGNATED AND MAY NOT BE VALID FOR SUCH MATERIAL USED
IN COMBINATION WITH ANY OTHER MATERIALS OR IN ANY PROCESS.
SUCH INFORMATION IS, TO THE BEST OF THE COMPANYS KNOWLEDGE AND BELIEF,
ACCURATE AND RELIABLE AS OF THE DATE INDICATED.
HOWEVER, NOR WARRANTY, GUARANTEE OR REPRESENTATION IS MADE AS TO ITS
ACCURACY, RELIABILITY OR COMPLETENESS. IT
IS THE USERS RESPONSIBILITY TO SATISFY HIMSELF AS TO THE SUITABILITY OF SUCH
INFORMATION FOR HIS OWN PARTICULAR USE.
HYDROBREAKÒ
DR
MARKET PLACE:
As an alternative to solvents or high alkaline
based detergents in cleaning and degreasing processes involving metals including
brass, copper and aluminium, plastic or glass components.
With HYDROBREAKÒ DR
containing no chlorinated solvents, caustics, silicates or phosphates, it can be
used as a totally safe alternative in cleaning/degreasing baths or spray
systems. Manufacturing industry,
engineering, and service industry.
PRODUCT DESCRIPTION:
A non-toxic low vapour fluid
with non-foaming properties when used above 55°C.
HYDROBREAKÒ DR
has all the benefits of a totally safe product, with excellent
cleaning/degreasing performance.
TYPICAL USES:
Hot water spray cleansing and
degreasing systems for the preparation of component parts as part of
manufacturing process.
BENEFITS:
Totally safe in use (no
caustics, solvents or silicates). Lasts longer than conventional cleaners.
Non-foaming must be used above 55°C.
Prevents oil and grease and slime build-up in equipment. The use of HydrobreakÒ DR
also prevents the build up of scale in the wash plant, which ensures more
efficient wash plant operation, and it also keeps machinery cleaner during use
giving reduced maintenance costs for the equipment.
Prevents sludge build-up. Aids
biodegradation of oils, greases and other hydrocarbon material.
Very effective and economical in use. An environmentally acceptable
product which minimises otherwise expensive disposal costs. Can be used to clean
and brighten brass, aluminium.
DILUTION RATES:
For normal cleaning
applications use at a 1-5% dilution ratio. For heavy contamination and for use
as a metal brightener use at 5-10%.
PACKAGING:
25 and 205 litre
non-returnable containers
TECHNICAL
INFORMATION DATA - HYDROBREAKÒ DR
PHYSICAL
FORM:
LIQUID
COMPOSITION
OF PRODUCT:
AN AQUEOUS BLEND OF FULLY BIODEGRADABLE NON-IONIC SURFACTANTS, ORGANIC
ACIDS AND PLANT EXTRACTS
APPEARANCE:
PALE YELLOW/BROWN
ODOUR:
SLIGHT
MISCIBILITY
WITH WATER:
COMPLETE
SPECIFIC
GRAVITY @ 20 DEG C:
1.028-1.032
P.H.:
6.0 +/- 1.0
BOILING
POINT:
100 DEG. C
FREEZING
POINT:
0 DEG. C
FLASH POINT:
> 65 DEG. C NON-FLAMMABLE
FLASH POINT
METHOD:
TCC (TAG CLOSED CUP)
DEGRADABILITY:
> 97% GERMAN LAW
TRANSPORT
INFORMATION:
THIS PRODUCT IS NOT CONSIDERED HAZARDOUS FOR TRANSPORT
STORAGE
REQUIREMENTS:
STORE IN PLASTIC CONTAINERS ABOVE 0 DEG.C
SAFETY
REQUIREMENTS:
THIS PRODUCT IS CLASSIFIED NON-HARMFUL
WHILST THERE ARE NO SPECIFIC RECOMMENDATIONS WITH
REGARD TO HYDROBREAKÒ DR, PROTECTIVE GOGGLES AND
GLOVES SHOULD BE WORN WHEN HANDLING ANY SUBSTANCE
SAFETY
DATA SHEET
1.
IDENTIFICATION OF THE PREPARATION
SUBSTANCE NAME:
HYDROBREAKÒ
DR
COMPANYNAME:
TechnoSol Limited
EMERGENCY PHONE NUMBER:
+ 372 51 61 403
2.
COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT NAME
CONTENTS
HEALTH
RISK
(class)
(R No.)
An aqueous blend of fully biodegradable
surfactants, organic acids and plant extracts
None
None
3.
HAZARDOUS IDENTIFICATION
Not regarded as a health
hazard under current legislation.
4. FIRST AID MEASURES
EYES:
Promptly wash eyes with lots of water while lifting the eye lids.
Get medical attention immediately. Continue to rinse.
SKIN:
Remove affected person from source of contamination.
Promptly flush contaminated skin with soap or mild detergent and water.
Promptly remove clothing if penetrated and flush the skin with water.
Get medical attention if irritation persists after washing.
INHALATION:
In the unlikely event of inhalation caused by faulty work practices, move
the exposed person to fresh air at once. Perform
artificial respiration if breathing has stopped.
Keep the affected person warm and at rest.
Get prompt medical attention.
INGESTION:
NEVER MAKE AN UNCONSCIOUS PERSON VOMIT OR DRINK FLUID! IF PERSON IS
CONSCIOUS, let affected person drink lots of water to dilute the swallowed
chemical. Seek medical attention.
5. FIRE
FIGHTING MEASURES
HYDROBREAK DR
is non-flammable and would only cause problems under extreme conditions
EXTINGUISHING MEDIA
alcohol foam carbon dioxide (CO2), dry chemicals, sand, dolomite,
etc. are unaffected by HYDROBREAKÒ
DR.
SPECIAL FIRE FIGHTING
Use water to keep exposed containers cool
PROCEDURES:
and disperse vapours. Water
spray may be used to flush spills away from exposures and dilute spills.
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS:
monoxide (CO) could be given off under extreme conditions.
6. ACCIDENTAL RELEASE MEASURES
SPILL CLEAN-UP METHODS:
Ventilate. Clean-up
personnel should use liquid contact protection.
Wash thoroughly after dealing with spillage.
SMALL SPILLS:
Absorb onto sand or other inert material and sweep up into suitable
container.
LARGE SPILLS:
Prevent the spillage from entering drains, ditches and rivers by use of
cellulose absorbents, sand or earth. Inform
local authorities if this cannot be prevented.
7.
HANDLING AND STORAGE
USAGE PRECAUTIONS:
Avoid spillage, skin and eye contact.
Avoid forming mists or fogs.
STORAGE PRECAUTIONS:
Store in plastic containers at temperatures above 0 degrees C. Keep
containers closed during storage.
8.
EXPOSURE CONTROLS AND PER7SONAL PROTECTION
INGREDIENT NAME
STD
LT EXP
ST EXP
(8 hrs.)
(10 min.)
does not apply
PROTECTIVE EQUIPMENT
Gloves and goggles should be worn when handling any chemical
RESPIRATORS:
No specific recommendations made.
PROTECTIVE GLOVES:
Use suitable protective gloves if risk of skin contact.
EYE PROTECTION:
Wear splash-proof eye goggles to prevent any possibility of eye contact.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
Liquid colourless or with A pale yellow tint
ODOUR/TASTE:
Slight
SOLUBILITY DESCRIPTION:
Miscible with water
SPECIFIC GRAVITY (Water = 1):
1.030 @ 20C
FLASH POINT (C):
>65 degree C. This
product is non-flammable
FLASH POINT METHOD
TCC (Tag closed cup)
10. STABILITY AND REACTIVITY
STABILITY:
No particular stability concerns
MATERIALS TO AVOID:
None
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon monoxide (CO) could be given off
under extreme conditions
11. TOXICOLOGICAL INFORMATION
TOXIC DOSE 1 (LD 50):
No information available
TOXIC CONS. (LC 50):
HEALTH WARNINGS:
May be an irritant of eyes and mucous membranes after prolonged exposure
HEALTH SYMPTOMS:
Irritation of eyes and mucous membranes
ACUTE AND CHRONIC
No known chronic or acute health risks
HEALTH HAZARDS:
12. ECOLOGICAL INFORMATION
DEGRADABILITY:
>97% (German Law)
ACUTE FISH TOXICITY:
No information available
WATER HAZARD
May be slight pollutant based on reactants
CLASSIFICATION
13. DISPOSAL CONDITIONS
DISPOSAL METHODS:
Confirm disposal procedures with environmental engineer and local
regulations
14. TRANSPORT INFORMATION
UD No.:
This product is not considered hazardous
ADR CLASS No.:
for transport
AIR TRANSPORT CLASS:
-
AIR SUB-CLASS:
-
AIR PACK GR.:
-
HAZCHEM CODE:
-
SEA TRANSPORT CLASS No.:
-
SEA PACK GR.:
-
RAIL TRANSPORT CLASS No.:
-
CEFIC TEC (R) No.:
-
UK LABEL FOR CONVEYANCE:
-
PRODUCT COMMODITY CODE
3402 - 9010
15. REGULATORY INFORMATION
LABEL FOR SUPPLY:
No classification given
RISK PHRASES:
Not classified
SAFETY PHRASES:
Wear suitable gloves and eye protection
UK REGULATORY REFERENCES:
Health And Safety At Work Act 1974. The Control of Substances Hazardous
to Health Regulations 1988 Chemical (Hazard Information and Packaging)
Regulations
16. OTHER INFORMATION
USER NOTES:
REVISION DATE:
1.10.00
REVISION NO./REPLACES
1/All previous health and safety
SDS ISSUED:
data sheets
DISCLAIMER
THIS
INFORMATION RELATES ONLY TO THE SPECIFIC MATERIAL DESIGNATED AND MAY NOT BE
VALID FOR SUCH MATERIAL USED IN COMBINATION WITH ANY OTHER MATERIALS OR IN ANY
PROCESS. SUCH INFORMATION IS, TO
THE BEST OF THE COMPANYS KNOWLEDGE AND BELIEF, ACCURATE AND RELIABLE AS OF
THE DATE INDICATED. HOWEVER, NOR
WARRANTY, GUARANTEE OR REPRESENTATION IS MADE AS TO ITS ACCURACY, RELIABILITY OR
COMPLETENESS. IT IS THE USERS
RESPONSIBILITY TO SATISFY HIMSELF AS TO THE SUITABILITY OF SUCH INFORMATION FOR
HIS OWN PARTICULAR USE.
HYDROBREAKÒ HD
MARKET PLACE:
As an alternative to solvent
based cleaning and degreasing processes involving metal, glass and plastic
components. With HYDROBREAKÒ HD
containing no butyl or chlorinated solvents or caustics, it can be used as an
alternative in cleaning/degreasing baths or spray systems.
Manufacturing industry, engineering, servicing industry.
PRODUCT DESCRIPTION:
A non-toxic low vapour fluid
with non-foaming properties if used above 50°C and
built-in short-term rust inhibition properties.
HYDRBREAKÒ HD has been designed to
remove stubborn deposits of dirt, grease and grime.
TYPICAL USES:
Hot water spray cleansing and
degreasing systems for the preparation of component parts as part of
manufacturing or refurbishment process.
BENEFITS:
Very effective against heavier
contamination deposits. Lasts longer than conventional cleaners.
Non-foaming must be used above 50°C.
Inbuilt short-term corrosion inhibition system.
Prevents oil and grease build-up in equipment.
Keeps machinery cleaner during use giving reduced maintenance costs for
the equipment. Very effective and economical in use.
Can be used on aluminium, brass and copper for heavier contamination
removal.
DILUTION RATES:
Effective use up to 100:1
General use 20:1
PACKAGING:
25 and 205 litre
non-returnable containers
SAFETY
DATA SHEET
1.
IDENTIFICATION OF THE PREPARATION
SUBSTANCE NAME:
HYDROBREAKÒ HD
COMPANY IDENTIFICATION:
TechnoSol Limited
EMERGENCY TELEPHONE NUMBER:
+372 51 61 403
2.
COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT NAME:
CONTENTS
HEALTH
RISK
(class)
(R No.)
An aqueous blend of
surfactants and inhibitors
Xi
36,38
3.
HAZARDS IDENTIFICATION:
Irritating to skin and eyes.
4.
FIRST AID MEASURES:
EYES:
Promptly wash eyes with lots of water while lifting the eye lids.
Get medical attention immediately. Continue to rinse.
SKIN:
Remove affected person from source of contamination.
Promptly flush contaminated skin with soap or mild detergent and water.
Promptly remove clothing if penetrated
and flush the skin with water. Get
medical attention if irritation persists after washing.
INHALATION:
In the unlikely event of inhalation caused by faulty work practices, move
the exposed person to fresh air at once. Perform
artificial respiration if breathing has stopped.
Keep the affected person warm and at rest. Get prompt medical attention.
INGESTION:
NEVER MAKE UNCONSCIOUS PERSON VOMIT OR DRINK FLUIDS. If person is
conscious, let affected person drink lots of water to dilute the swallowed
chemical. Seek medical attention.
5.
FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA:
alcohol foam carbon dioxide (CO2), dry chemicals, sand, dolomite,
etc. are unaffected by HYDROBREAKÒ HD
SPECIAL FIRE FIGHTING:
Use water to keep exposed containers cool
PROCEDURES:
and disperse vapours. Water
spray may be used to flush spills away from exposures and dilute spills.
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS:
monoxide (CO) could be given off under extreme conditions
6.
ACCIDENTAL RELEASE MEASURES
SPILL CLEAN-UP METHODS:
Ventilate. Clean-up
personnel should use liquid contact protection.
Wash thoroughly after dealing with spillage.
SMALL SPILLS:
Absorb onto sand or other inert material and sweep up into suitable
container.
LARGE SPILLS:
Prevent the spillage from entering drains, ditches and rivers by use of
cellulose absorbents, sand or earth. Inform
local authorities if this cannot be prevented.
7.
HANDLING AND STORAGE
USAGE PRECAUTIONS:
Avoid spillage, skin and eye contact.
Avoid forming mists or fogs.
STORAGE PRECAUTIONS:
Store in plastic containers at temperatures above 0 degrees C. Keep
containers closed during storage.
8.
EXPOSURE CONTROLS AND PERSONAL PROTECTION
INGREDIENT NAME:
STD
LT EXP
ST EXP
(8 hrs.)
(10 min.)
PROTECTIVE EQUIPMENT:
Gloves and goggles should be worn when handling any chemical
RESPIRATORS:
No specific recommendations made.
PROTECTIVE GLOVES:
Use suitable protective gloves if risk of skin contact.
EYE PROTECTION:
Wear splash-proof eye goggles to prevent any possibility of eye contact.
9.
PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE:
Clear liquid
COLOUR:
None
ODOUR/TASTE:
Slight
SOLUBILITY DESCRIPTION:
Miscible with water
SPECIFIC GRAVITY (Water = 1):
1.0395 @ 20C
FLASH POINT (C):
>65 degree C. This
product is non-flammable
FLASH POINT METHOD:
TCC (Tag closed cup)
pH value:
10 +/- 1.0
10.
STABILITY AND REACTIVITY
STABILITY:
No particular stability concerns
MATERIALS TO AVOID:
None
HAZARDOUS DECOMPOSITION
Toxic gases/vapours/fumes of carbon
PRODUCTS
monoxide (CO) could be given off under extreme conditions
11.
TOXICOLOGICAL INFORMATION
TOXIC DOSE 1 (LD 50):
No information available
TOXIC CONS. (LC 50):
HEALTH WARNINGS:
May be an irritant of eyes and mucous membranes
HEALTH SYMPTOMS:
Irritation of eyes and mucous membranes
ACUTE AND CHRONIC
No known chronic or acute health risks
HEALTH HAZARDS:
12.
ECOLOGICAL INFORMATION
DEGRADABILITY:
No information available.
ACUTE FISH TOXICITY:
No information available
WATER HAZARD
May be slight pollutants based on
CLASSIFICATION:
reactants
13.
DISPOSAL CONDITIONS
DISPOSAL METHODS:
Confirm disposal procedures with environmental engineer and local
regulations
14.
TRANSPORT INFORMATION
UD No.:
This product is not considered hazardous
ADR CLASS No.:
for transport
AIR TRANSPORT CLASS:
-
AIR SUB-CLASS:
-
AIR PACK GR.:
-
HAZCHEM CODE:
-
SEA TRANSPORT CLASS No.:
-
SEA PACK GR.:
-
RAIL TRANSPORT CLASS No.:
-
CEFIC TEC (R) No.:
-
UK LABEL FOR CONVEYANCE:
-
INTERNATIONAL COMMODITY CODE
3402 9010
15.
REGULATORY INFORMATION
LABEL FOR SUPPLY:
IRRITANT
RISK PHRASES:
36/38 Irritating
to skin and eyes
SAFETY PHRASES:
37/39 Wear suitable gloves and eye
protection
26
In case of contact with eyes wash immediately with plenty of water and
seek medical advice
28
After contact with skin wash immediately with plenty of water.
UK REGULATORY REFERENCES:
Health And Safety At Work Act 1974. The Control of Substances Hazardous
to Health Regulations 1988 Chemical (Hazard Information and Packaging)
Regulations
16.
OTHER INFORMATION
USER NOTES:
REVISION DATE:
1.10.00
REVISION NO./REPLACES
1/All previous health and safety
COMMENTS:
New data sheet to CHIP format
DISCLAIMER
THIS INFORMATION RELATES ONLY TO THE SPECIFIC
MATERIAL DESIGNATED AND MAY NOT BE VALID FOR SUCH MATERIAL USED IN COMBINATION
WITH ANY OTHER MATERIALS OR IN ANY PROCESS.
SUCH INFORMATION IS, TO THE BEST OF THE COMPANYS KNOWLEDGE AND BELIEF,
ACCURATE AND RELIABLE AS OF THE DATE INDICATED.
HOWEVER, NOR WARRANTY, GUARANTEE OR REPRESENTATION IS MADE AS TO ITS
ACCURACY, RELIABILITY OR COMPLETENESS. IT
IS THE USERS RESPONSIBILITY TO SATISFY HIMSELF AS TO THE SUITABILITY OF SUCH
INFORMATION FOR HIS OWN PARTICULAR USE.